PRODUCT DATA SHEET
Product Reference Cyanoacrylate Adhesive PST24
PST24 is an ethyl Cyanoacrylate adhesive of medium viscosity. It is especially suitable for bonding rubbers, plastics and filled rubbers without loss of adhesive performance.
An excellent general purpose grade. Single component adhesive.
Bonds in seconds ceramics, rubbers & plastics 100% Solventless
Bonding of foams and filled rubbers Economical in use.
Rapid bonding at room temperatures
PERFORMANCE DATA, TYPICAL VALUES
Steel / steel substrate values
Tensile strength (ASTM D2095) 28-32 N/mm2 (3600-4400lbf/in2)
Tensile shear strength (ASTM D1002) 15-20 N/mm2 (2300-2700 lb/in2)
Impact strength (ASTM 95) 1.8-2.0 N/mm2 (8-9 lb/in2)
Physical properties of liquid adhesive
Monomer Ethyl cyanoacrylate
Specific gravity 1.05
Viscosity @ 25°C (Brookfield) 100-120 cPs
Flash point (Cleveland open cup) > 85° C
Shelf life (Stored below 25°C) 12 Months minimum
Physical properties of cured adhesive
Refractive index (ND20) 1.46
Hardness (Rockwell) 85
Specific resistance OHM/cm 8 x 1012
Dielectric constant @ 1MHZ 3.44
Softening point 150°C
Working temperature range -60°C to + 80°C
DIRECTIONS FOR USE
Ensure surfaces are clean and dry, apply adhesive to one surface. Press surfaces together and hold for 10 seconds or as indicated below. Cure speed is rapid so exercise care when aligning. Cure performance can be enhanced if necessary, by using selected activators.
TYPICAL BONDING TIMES
Plastics 5 - 60 seconds depending on substrates.
Rubbers 2 - 20 seconds depending on substrates.
Metals (degreased) 10 - 60 seconds depending on substrates.
Ensure surfaces are degreased prior to bonding. Ensure surfaces are close fitting.
This product is not suitable for permanent glass bonding, or applications where the bonded joint may be immersed in water.
RELATIVE HUMIDITY CONDITIONS
Where possible the working environment should have a relative humidity of 50% +. This will assist in efficient bonding of components with Cyanoacrylates. Relative humidities less than 50% and continued exposure can give rise to Cyanoacrylate vapours which can effect eyes, nose, and throat similar to an asthmatic effect.
Prior to use consult relevant Material Safety Data Sheet.
When continuously used local fume extraction is recommended.
Contains Cyanoacrylate Ester. Use in a well ventilated environment.
Bonds skin and eyes in seconds, wear safety goggles if danger of splashing.
In the event of inadvertent skin bonding separate bonded skin tissue carefully by peeling apart gently with a blunt instrument. Preferably after soaking in warm soapy water.
Use hand cream or disposable gloves.
Keep out of reach of children.
Store in original sealed upright container between +3°C and 20°C in a dry area out of direct sunlight. The lower the temperature the longer the ultimate shelf life, but bring to room temperature before use.
Available in 20g, 50g, and 500g packs.
Other packs available upon request.
Neither Polymer Systems Technology Limited, not their approved distributors accept any liability for loss or damage arising directly or indirectly from the use of this product. The data given is for information only and is based upon data we believe to be accurate and reliable. Before using any product it is the customers responsibility to satisfy themselves by appropriate trials that each product is suitable for their intended use. As the application and use of the product is outside the control of Polymer Systems Technology Limited, the user assumes all risk and liability whatsoever in connection herewith.
All materials supplied are subject to our standard terms and conditions of trading, a copy of which is available upon request.